Gentoo Logo

1.  Timezone

You first need to select your timezone so that your system knows where it is located. Look for your timezone in /usr/share/zoneinfo, then copy it to /etc/localtime. Please avoid the /usr/share/zoneinfo/Etc/GMT* timezones as their names do not indicate the expected zones. For instance, GMT-8 is in fact GMT+8.

Code Listing 1.1: Setting the timezone information

# ls /usr/share/zoneinfo
(Suppose you want to use GMT)
# cp /usr/share/zoneinfo/GMT /etc/localtime

1.  Installing the Sources

Choosing a Kernel

The core around which all distributions are built is the Linux kernel. It is the layer between the user programs and your system hardware. Gentoo provides its users several possible kernel sources. A full listing with description is available at the Gentoo Kernel Guide.

For PPC64 you should use gentoo-sources.

Code Listing 1.1: Installing a kernel source

# emerge gentoo-sources

When you take a look in /usr/src you should see a symlink called linux pointing to your kernel source. In this case, the installed kernel source points to gentoo-sources-${kernel-version}. Your version may be different, so keep this in mind.

Code Listing 1.1: Viewing the kernel source symlink

# ls -l /usr/src/linux
lrwxrwxrwx    1 root    root       12 Aug 10 11:04 /usr/src/linux -> linux-${kernel-version}

Now it is time to configure and compile your kernel source. There is the ability to use "genkernel" which would create a generic kernel like the ones used on the installation CDs, but it is not fully functional for PPC64 at the moment.

Continue now with Manual Configuration.

1.  Manual Configuration

Introduction

Manually configuring a kernel is often seen as the most difficult procedure a Linux user ever has to perform. Nothing is less true -- after configuring a couple of kernels you don't even remember that it was difficult ;)

However, one thing is true: you must know your system when you configuring a kernel manually. Most information can be gathered by emerging pciutils (emerge pciutils) which contains lspci. You will now be able to use lspci within the chrooted environment. You may safely ignore any pcilib warnings (like pcilib: cannot open /sys/bus/pci/devices) that lspci throws out. Alternatively, you can run lspci from a non-chrooted environment. The results are the same. You can also run lsmod to see what kernel modules the Installation CD uses (it might provide you with a nice hint on what to enable).

Code Listing 1.1: Invoking menuconfig

# cd /usr/src/linux
Important: In case you are in 32-bit userland, you must edit the top
level Makefile in /usr/src/linux and change the CROSS_COMPILE option to
CROSS_COMPILE ?= powerpc64-unknown-linux-gnu-. You must do this before you run
make menuconfig or it may result in kernel compilation problems.
# make menuconfig

You will be greeted with several configuration sections. We'll first list some options you must activate (otherwise Gentoo will not function, or not function properly without additional tweaks).

Activating Required Options

First go to File Systems and select support for the filesystems you use. Don't compile them as modules, otherwise your Gentoo system will not be able to mount your partitions. Also select Virtual memory, /proc file system, and /dev/pts file system for Unix98 PTYs:

Code Listing 1.1: Selecting necessary file systems

File systems --->
  [*] Virtual memory file system support (former shm fs)
  [*] /proc file system support
  [*] /dev/pts file system for Unix98 PTYs

(Select one or more of the following options as needed by your system)
  <*> Reiserfs support
  <*> Ext3 journalling file system support
  <*> JFS filesystem support
  <*> Second extended fs support
  <*> XFS filesystem support

Note: You will find some of the mentioned options under Pseudo filesystems which is a subpart of File systems.

If you are using PPPoE to connect to the Internet or you are using a dial-up modem, you will need the following options in the kernel (you will find the mentioned options under Networking support which is a subpart of Device Drivers):

Code Listing 1.1: Selecting PPPoE necessary drivers

Network device support --->
  <*> PPP (point-to-point protocol) support
  <*>   PPP support for async serial ports
  <*>   PPP support for sync tty ports

The two compression options won't harm but are not definitely needed, neither does the PPP over Ethernet option, that might only be used by ppp when configured to do kernel mode PPPoE.

If you require it, don't forget to include support in the kernel for your ethernet card.

When you're done configuring your kernel, continue with Compiling and Installing.

Compiling and Installing

Now that your kernel is configured, it is time to compile and install it. Exit the configuration and start the compilation process:

Code Listing 1.1: Compiling the kernel

# make && make modules_install

When the kernel has finished compiling, copy the kernel image to /boot. Remember to replace <kernel-version> with your actual kernel version:

Code Listing 1.1: Installing the kernel

# cp vmlinux /boot/<kernel-version>

Now continue with Configuring the Modules.

1.  Configuring the Modules

You should list the modules you want automatically loaded in /etc/modules.autoload.d/kernel-2.6. You can add extra options to the modules too if you want.

To view all available modules, run the following find command. Don't forget to substitute "<kernel version>" with the version of the kernel you just compiled:

Code Listing 1.1: Viewing all available modules

# find /lib/modules/<kernel version>/ -type f -iname '*.o' -or -iname '*.ko'

For instance, to automatically load the 3c59x.ko module, edit the kernel-2.6 file and enter the module name in it.

Code Listing 1.1: Editing /etc/modules.autoload.d/kernel-2.6

# nano -w /etc/modules.autoload.d/kernel-2.6

Code Listing 1.1: /etc/modules.autoload.d/kernel-2.6

3c59x

Continue the installation with (Configuring your System).

Page updated August 5, 2009

Donate to support our development efforts.

Copyright 2001-2014 Gentoo Foundation, Inc. Questions, Comments? Contact us.